Cards, Fall, Fall

Fall House Card and How to Make It Into A Box featuring Honey Bee Stamps

Ok, let’s talk about how much I love the House Builder Card Base Dies from Honey Bee Stamps!!! It is sooo much fun making houses and decorating them. There are probably a million combinations you can use with these dies. The add-on dies also allow you to expand you creativity; more on those later.

For the first card, I started by diecutting the house card base 2x, chimney, and 2 gables from Simon Says Stamp Fog 8-1/2″ X 11″ Cardstock and the roof, gable roof and stairs from Simon Says Stamp Slate 8-1/2″ X 11″ Cardstock. I adhered the two houses with the pre-scored strip that comes in the dieset to create the card base. Be sure to use double-sided tape or something very strong so they don’t come apart.

I diecut all the window frames, window boxes, shutters (from the Gingerbread House add-on) and fence from Neenah Classic Crest, 80lb Solar White. I used aqua cardstock from my stash for the door and a silver cardstock for the door handle, yellows and oranges for all the bushes and dark orange, yellow, orange and aqua for the flowers in the flower pots. I backed all the windows with a light aqua cardstock and used Lawn Fawn 6×6 Perfectly Plaid Fall Petite Paper Pack to diecut curtains for the bottom windows. I created the wreath by diecutting several of the leaf vine and stacking them on top of the wreath from the Gingerbread House add-on. I also diecut a pumpkin from the Haunted House Add-on.

On the inside of the card, I stamped the “Happy” sentiment from the Honey Bee Stamps Happy Fall Y’all 4×6 Stamp Set with Catherine Pooler Black Jack Ink and diecut the “Fall” from Happy Fall Y’all Honey Cuts with orange cardstock from my stash and adhered it under the “Happy”. Love this card!


Next, I wanted to see if I could turn this card into a box easily because it could house some fun gifts for the holidays or just anytime really. And it turns out you can. I’m sure there are some other ways to do this but I chose the simplest with the least amount of cutting. The process is exactly the same as the card except, you need to decorate 2x and add the sides and bottom piece.

I started by diecutting the house card base 2x again, 2 chimneys, and 2 gables from Simon Says Stamp Fog 8-1/2″ X 11″ Cardstock and 2 roofs, 2 gable roofs and 2 stairs from Stampin’ Up! Early Espresso 8-1/2″ X 11″ Cardstock. I decorated the two houses before I adhered them to the side pieces for the box. This one was decorated much like the previous card, with the following exceptions: I used a red cardstock for the door, a different pattern for the curtains from Lawn Fawn’s 6×6 Perfectly Plaid Fall Petite Paper Pack, diecut the tree from the Haunted House Add-on with Stampin’ Up! Early Espresso 8-1/2″ X 11″ Cardstock and added several pumpkins, diecut from the same set. I did the same thing to both houses.

Ok, let’s turn these into a box! This will require just one piece of letter or A4 cardstock. First, I cut a piece of Simon Says Stamp Fog 8-1/2″ X 11″ Cardstock (same as the houses) to 3 x 9-7/8″and one to 3 x 4-1/4″. Then scored both pieces 1/2″ in from each side on the short side (holding your paper vertically) and 1-1/2″ (only scored the first section of the longer piece) and diagonal score lines from the 1-1/2″ score line to the left and right corners (see diagram below). I turned the longer (9-7/8″ long) piece 90 degrees and scored at 4-1/4″, and 9-3/8″. Folded and burnished all the scorelines and to make it easier to assemble, making sure to fold the center and diagonal score lines in both directions. This will allow the box to fold in on each side like an accordian.

I cut a little triangle 1/2″ in on the flaps where the score lines fall and the end flaps as well but only on the longer piece. I’ve included a PDF of the below diagram that you can download and print.

I used double-sided tape to adhere the sides and bottom of the box together and to the cards. I folded up all the tabs and adhered the two pieces together. You will want to adhere the second side piece to the side of the longer piece that has a 1/2″ tab (labeled bottom on diagram) then adhere your houses on either side of the box (you can see on the first of four images below how it sits against the side piece. Once the box was assembled, I used an 1/8″ punch to punch a hole in the top center of the two sides of the box and tied it with some 1/4″ red satin ribbon.

I also made a cute tag to go with it. I cut a piece of Simon Says Stamp Fog 8-1/2″ X 11″ Cardstock to 2 x 3-1/2″ and use the Stampin’ Up! Scalloped Tag Topper Punch on one end. I diecut a fence and one bush from House Builder Card Base Dies and adhered it to the tag. I stamped the “Happy” sentiment from the Honey Bee Stamps Happy Fall Y’all 4×6 Stamp Set with Catherine Pooler Black Jack Ink and diecut the “Fall” from Happy Fall Y’all Honey Cuts with red cardstock from my stash and adhered it under the “Happy”. I love how this came out!

Supplies

Thanks for reading this post. I hope you enjoyed and I’ve inspired you to try out these adorable House Builder dies and make some fun cards and gift boxes! Leave comments or questions below or feel free to email me.

2 thoughts on “Fall House Card and How to Make It Into A Box featuring Honey Bee Stamps”

  1. Oh my gosh….I LOVE these two houses! And bonus…I had bought the dies from HB but had not yet used them. Thanks for the inspiration…and the template! Very creative and love your choice of Fall colors! So, so cute!!

Leave a Reply